writing to /dev/stdout
reading from traces/H31an42.hex

begin parsing...


->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->
it all started when the Network Terminator said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       1] C/R flag says COMMAND 
[ 1111111] TEI is 0x7F (broadcast address)

Unnumbered Block: [oooooo11]
[     ooo] UI- unnumbered information
[       o] POLL bit is 0
->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->




<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-
and then, 00:00:00:001 later, the Terminal Equipment said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       o] C/R flag says COMMAND 
[ 1o1o1oo] TEI is 0x54 (dynamic address)

Unnumbered Block: [o1111111]
[     o11] SABME- set asynchronous balance extended mode
[       1] POLL bit is 1
<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-




->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->
and then, 00:00:00:060 later, the Network Terminator said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       o] C/R flag says RESPONSE
[ 1o1o1oo] TEI is 0x54 (dynamic address)

Unnumbered Block: [o111oo11]
[      oo] UA- unnumbered acknowledgment
[       1] FINAL bit is 1
->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->




<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-
and then, 00:00:00:287 later, the Terminal Equipment said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       o] C/R flag says COMMAND 
[ 1o1ooo1] TEI is 0x51 (dynamic address)

Unnumbered Block: [o1111111]
[     o11] SABME- set asynchronous balance extended mode
[       1] POLL bit is 1
<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-




->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->
and then, 00:00:00:051 later, the Network Terminator said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       o] C/R flag says RESPONSE
[ 1o1ooo1] TEI is 0x51 (dynamic address)

Unnumbered Block: [o111oo11]
[      oo] UA- unnumbered acknowledgment
[       1] FINAL bit is 1
->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->




<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-
and then, 00:00:00:099 later, the Terminal Equipment said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       o] C/R flag says COMMAND 
[ 1o1ooo1] TEI is 0x51 (dynamic address)

Information Block:
[ ooooooo] N(S) is 0x0
[ ooooooo] N(R) is 0x0
[       o] Poll bit is 0

Layer3 Info:
[oooo1ooo] Euro ISDN
[ooooooo1] Call Reference Length is 0x01
[       1] Partner
[ o11oo1o] Call Reference Number is 0x32
[ooooooo1] ALERTING

<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-




->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->
and then, 00:00:00:122 later, the Network Terminator said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       o] C/R flag says RESPONSE
[ 1o1ooo1] TEI is 0x51 (dynamic address)

Supervisory Block:
[      oo] S bits say RR- receiver ready
[ oooooo1] N(R) is 1
[       o] FINAL bit is 0
->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->




->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->
and then, 00:00:09:335 later, the Network Terminator said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       1] C/R flag says COMMAND 
[ 1o1o1oo] TEI is 0x54 (dynamic address)

Supervisory Block:
[      oo] S bits say RR- receiver ready
[ ooooooo] N(R) is 0
[       1] POLL bit is 1
->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->




<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-
and then, 00:00:00:004 later, the Terminal Equipment said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       1] C/R flag says RESPONSE
[ 1o1o1oo] TEI is 0x54 (dynamic address)

Supervisory Block:
[      oo] S bits say RR- receiver ready
[ ooooooo] N(R) is 0
[       1] FINAL bit is 1
<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-




->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->
and then, 00:00:00:460 later, the Network Terminator said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       1] C/R flag says COMMAND 
[ 1o1ooo1] TEI is 0x51 (dynamic address)

Supervisory Block:
[      oo] S bits say RR- receiver ready
[ oooooo1] N(R) is 1
[       1] POLL bit is 1
->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->




<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-
and then, 00:00:00:127 later, the Terminal Equipment said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       1] C/R flag says RESPONSE
[ 1o1ooo1] TEI is 0x51 (dynamic address)

Supervisory Block:
[      oo] S bits say RR- receiver ready
[ ooooooo] N(R) is 0
[       1] FINAL bit is 1
<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-




<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-
and then, 00:00:00:094 later, the Terminal Equipment said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       o] C/R flag says COMMAND 
[ 1o1ooo1] TEI is 0x51 (dynamic address)

Information Block:
[ oooooo1] N(S) is 0x1
[ ooooooo] N(R) is 0x0
[       o] Poll bit is 0

Layer3 Info:
[oooo1ooo] Euro ISDN
[ooooooo1] Call Reference Length is 0x01
[       1] Partner
[ o11oo1o] Call Reference Number is 0x32
[ooooo111] CONNECT
data:
[o1oo11oo] 0x4C
[ooooo1oo] 0x04
[ooooooo1] 0x01
[1ooooooo] 0x80
[oo11o1oo] 0x34
[oo11oo1o] 0x32

<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-




->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->
and then, 00:00:00:120 later, the Network Terminator said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       o] C/R flag says RESPONSE
[ 1o1ooo1] TEI is 0x51 (dynamic address)

Supervisory Block:
[      oo] S bits say RR- receiver ready
[ ooooo1o] N(R) is 2
[       o] FINAL bit is 0
->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->




->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->
and then, 00:00:00:189 later, the Network Terminator said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       1] C/R flag says COMMAND 
[ 1o1ooo1] TEI is 0x51 (dynamic address)

Information Block:
[ ooooooo] N(S) is 0x0
[ ooooo1o] N(R) is 0x2
[       o] Poll bit is 0

Layer3 Info:
[oooo1ooo] Euro ISDN
[ooooooo1] Call Reference Length is 0x01
[       o] Initiator
[ o11oo1o] Call Reference Number is 0x32
[oooo1111] CONNECT_ACKNOWLEDGE

->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->




<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-
and then, 00:00:00:086 later, the Terminal Equipment said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       1] C/R flag says RESPONSE
[ 1o1ooo1] TEI is 0x51 (dynamic address)

Supervisory Block:
[      oo] S bits say RR- receiver ready
[ oooooo1] N(R) is 1
[       o] FINAL bit is 0
<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-




<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-
and then, 00:00:04:023 later, the Terminal Equipment said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       o] C/R flag says COMMAND 
[ 1o1o1oo] TEI is 0x54 (dynamic address)

Unnumbered Block: [o1o1oo11]
[     o1o] DISC- disconnect
[       1] POLL bit is 1
<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-




->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->
and then, 00:00:00:028 later, the Network Terminator said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       o] C/R flag says RESPONSE
[ 1o1o1oo] TEI is 0x54 (dynamic address)

Unnumbered Block: [o111oo11]
[      oo] UA- unnumbered acknowledgment
[       1] FINAL bit is 1
->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->




->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->
and then, 00:00:03:280 later, the Network Terminator said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       1] C/R flag says COMMAND 
[ 1o1ooo1] TEI is 0x51 (dynamic address)

Information Block:
[ oooooo1] N(S) is 0x1
[ ooooo1o] N(R) is 0x2
[       o] Poll bit is 0

Layer3 Info:
[oooo1ooo] Euro ISDN
[ooooooo1] Call Reference Length is 0x01
[       o] Initiator
[ o11oo1o] Call Reference Number is 0x32
[o1ooo1o1] DISCONNECT
data:
[oooo1ooo] 0x08
[oooooo1o] 0x02
[1ooooooo] 0x80
[1oo1oooo] 0x90
[ooo111oo] 0x1C
[ooo1o1o1] 0x15
[1oo1ooo1] 0x91
[1o1oooo1] 0xA1
[ooo1oo1o] 0x12
[oooooo1o] 0x02
[oooooo1o] 0x02
[ooooo1o1] 0x05
[oooooooo] 0x00
[oooooo1o] 0x02
[ooooooo1] 0x01
[oo1oo1oo] 0x24
[oo11oooo] 0x30
[oooo1oo1] 0x09
[oo11oooo] 0x30
[ooooo111] 0x07
[1o1oooo1] 0xA1
[ooooo1o1] 0x05
[oo11oooo] 0x30
[oooooo11] 0x03
[oooooo1o] 0x02
[ooooooo1] 0x01
[oooooooo] 0x00
[ooo1111o] 0x1E
[oooooo1o] 0x02
[1oooooo1] 0x81
[1ooo1ooo] 0x88

->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->




<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-
and then, 00:00:00:173 later, the Terminal Equipment said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       1] C/R flag says RESPONSE
[ 1o1ooo1] TEI is 0x51 (dynamic address)

Supervisory Block:
[      oo] S bits say RR- receiver ready
[ ooooo1o] N(R) is 2
[       o] FINAL bit is 0
<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-




<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-
and then, 00:00:02:254 later, the Terminal Equipment said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       o] C/R flag says COMMAND 
[ 1o1ooo1] TEI is 0x51 (dynamic address)

Information Block:
[ ooooo1o] N(S) is 0x2
[ ooooo1o] N(R) is 0x2
[       o] Poll bit is 0

Layer3 Info:
[oooo1ooo] Euro ISDN
[ooooooo1] Call Reference Length is 0x01
[       1] Partner
[ o11oo1o] Call Reference Number is 0x32
[o1oo11o1] RELEASE
data:
[oooo1ooo] 0x08
[oooooo1o] 0x02
[1ooooooo] 0x80
[1oo1oooo] 0x90

<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-




->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->
and then, 00:00:00:145 later, the Network Terminator said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       o] C/R flag says RESPONSE
[ 1o1ooo1] TEI is 0x51 (dynamic address)

Supervisory Block:
[      oo] S bits say RR- receiver ready
[ ooooo11] N(R) is 3
[       o] FINAL bit is 0
->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->




->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->
and then, 00:00:00:087 later, the Network Terminator said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       1] C/R flag says COMMAND 
[ 1o1ooo1] TEI is 0x51 (dynamic address)

Information Block:
[ ooooo1o] N(S) is 0x2
[ ooooo11] N(R) is 0x3
[       o] Poll bit is 0

Layer3 Info:
[oooo1ooo] Euro ISDN
[ooooooo1] Call Reference Length is 0x01
[       o] Initiator
[ o11oo1o] Call Reference Number is 0x32
[o1o11o1o] RELEASE_COMPLETE

->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->




<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-
and then, 00:00:00:105 later, the Terminal Equipment said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       1] C/R flag says RESPONSE
[ 1o1ooo1] TEI is 0x51 (dynamic address)

Supervisory Block:
[      oo] S bits say RR- receiver ready
[ ooooo11] N(R) is 3
[       o] FINAL bit is 0
<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-




->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->
and then, 00:00:03:855 later, the Network Terminator said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       1] C/R flag says COMMAND 
[ 1o1ooo1] TEI is 0x51 (dynamic address)

Unnumbered Block: [o1o1oo11]
[     o1o] DISC- disconnect
[       1] POLL bit is 1
->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->->




<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-
and then, 00:00:00:031 later, the Terminal Equipment said:


Address Field:
[  oooooo] SAPI is 0x00 (call control procedure)
[       1] C/R flag says RESPONSE
[ 1o1ooo1] TEI is 0x51 (dynamic address)

Unnumbered Block: [o111oo11]
[      oo] UA- unnumbered acknowledgment
[       1] FINAL bit is 1
<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-




...end parsing